Power consumption is one of the last specifications buyers check and one of the first that matters once the machine is running. A machine that draws a lot of power requires a dedicated circuit, adds to the electricity bill, and may need ventilation or cooling. A machine that draws little power can be placed anywhere and adds almost nothing to operating cost. The Aircosan RA10 draws 350W, and understanding what that number means in practice is what allows a buyer to plan the electrical side of the installation.
Start with what 350W actually represents. A kilowatt-hour is 1,000 watts used for one hour. The RA10 running continuously for an hour would use 0.35 kWh. At a typical industrial electricity rate, that is a few cents per hour. The machine does not run continuously, because the operator stops it to pack, so the real consumption is lower than the continuous figure. The point is that the machine's energy cost is small enough that it does not appear as a line item in the operating budget, which is different from machines that draw several kilowatts.
The first practical effect is circuit planning. A 350W machine can share a circuit with other bench equipment rather than requiring a dedicated line. A packing bench may have a label printer, a tape dispenser, and a computer, and the combined draw is still within the capacity of a standard circuit. This means the machine can be placed where the work is rather than where the electrical panel allows, and the placement freedom is the practical value of the low draw.
The second practical effect is voltage flexibility. The RA10 supports 110V or 220V, which means the machine can be configured for the destination facility's standard. A facility with 110V outlets and a facility with 220V outlets can both use the machine without a transformer. The dual voltage support is part of the deployment freedom, and the deployment freedom is what allows the machine to be installed in facilities that were not designed with packaging equipment in mind.
The third practical effect is heat. A machine that draws a lot of power generates a lot of heat, and the heat has to be managed in the facility. A 350W machine generates a small amount of heat, which means it does not require additional ventilation or cooling. For a facility in a warm climate, this matters, because the heat from equipment adds to the cooling load. The RA10's low draw means the machine does not contribute to that load.
The fourth practical effect is noise. Power draw is not the same as noise, but the two are related, because a machine that draws a lot of power usually has a larger motor and a larger motor usually produces more noise. The RA10's 350W motor is modest, which means the motor runs quietly and the machine does not require hearing protection. The quiet operation is part of why the machine can sit at the packing bench rather than in a separate room.
The fifth practical effect is the generator or UPS requirement. A facility that uses a generator or an uninterruptible power supply has to size the system for the equipment it supports. A 350W machine is a small addition to the load, which means it does not change the sizing of the system. A machine that draws several kilowatts would change the sizing, and the change would be a cost that the buyer did not anticipate.
The specifications that interact with the power draw are worth knowing. The machine runs on 110V or 220V, draws 350W, and operates on 50-60HZ. Working speed is 32 m/min, forming width is 10cm±2cm, and the machine supports standard 32CM roll paper with 40CM available as a customization. It works with 70gsm and 80gsm three-fold paper. Net weight is 130kg, gross weight is 150kg, and the package dimensions are 1500mm*1000mm*1000mm. The vertical design measuring 930mm*763mm*1378mm with casters allows the machine to be placed at the bench.
The safety features do not change the power draw, but they do change how the power is used. The material-out alarm stops the motor and cutter automatically when paper runs out, which means the machine does not run without producing pads. The cover-open alarm prevents the machine from starting when the guard is open, which means the machine does not draw power while it is being serviced. The low-material warning prompts refilling in advance, which means the machine does not run dry. Each feature reduces the time the machine is drawing power without producing, which reduces the energy cost further.
Aircosan provides 1-on-1 after-sales service, product operation videos, and R&D online video guidance, and the service is relevant to the power question because the voltage configuration is part of the installation. A buyer who is unsure about the destination facility's voltage can ask, and the answer determines the configuration.
The honest limitation is that the power draw is not the only cost of operation. The paper is a consumable, the maintenance is a cost, and the operator's time is a cost. The 350W draw is small relative to those costs, which means the power is not the deciding factor in the purchase. It is the factor that makes the purchase easier to justify.
The practical takeaway is to check the power draw before the purchase and to confirm the voltage configuration for the destination facility. Aircosan evaluates paper width, daily usage, packing scenario, and space conditions before recommending a configuration, and the power is part of that evaluation. Most buyers do not check the power until the electrician asks, which is the late version of a question that the datasheet already answers. The 350W draw and the 110V or 220V support mean the answer is usually yes, and the yes is what allows the machine to be placed where it is needed.